利用电磁法研究HMX与TATB混合钝感炸药的冲击起爆特性

为研究含有少量奥克托金(HMX)且以三氨基三硝基苯(TATB)为基的高能钝感炸药PBX-3的冲击起爆反应增长规律,采用火炮驱动蓝宝石飞片的方法和铝基组合式电磁粒子速度计技术进行了一维平面冲击实验。通过实验测量撞击表面及内部不同深度处的冲击波后粒子速度,得到PBX-3炸药的Hugoniot关系。根据冲击波示踪器所测数据绘制了炸药到爆轰的时间-距离(x-t)图,获得了反映炸药冲击起爆性能的Pop关系。将入射压力为12.964 GPa时达到爆轰的6条速度曲线修整成相同零点,通过读取6条曲线的分离点即反应区末端的C-J点,计算出化学反应区时间和宽度。     

埋层界面和空气表面和频光谱信号贡献的调控

本文研究表明通过膜厚控制和表面等离激元增强方法可有效区分隐藏界面和空气表面的和频振动光谱信号. 以氟化钙基底支撑的PMMA薄膜为模型，观察到隐藏界面和空气表面对和频信号贡献的变化. 通过监控羰基和甲基伸缩振动基团，发现薄PMMA膜的和频信号来自PMMA/空气表面的化学基团-CH₂、-CH₃、-OCH₃和C=O，而厚PMMA膜的和频信号则来自基底/PMMA埋层界面的-OCH₃和C=O基团. 随制膜浓度增大，埋层界面C=O基团的取向角从65°下降到43°，且浓度大于或等于0.5 wt%时，取向角等于45°±2°. 相比之下，空气表面C=O的取向角落在21°∽38°之间. 在金纳米棒存在条件下，表面等离激元可以极大地增强和频信号，尤其是来自埋层界面信号.     

光子晶体光纤温度压力传感器

提出了一种在高温环境下同时测量温度和气压的光子晶体光纤温度压力传感器.在普通单模光纤和光子晶体光纤之间熔接一段空心光纤构成干涉结构.空心光纤段构成非本征法布里-珀罗干涉仪,利用光子晶体光纤的微孔与外界相通,通过气体折射率变化来测量环境中的气压变化;光子晶体光纤段构成本征法布里-珀罗干涉仪,利用热膨胀效应和热光效应来测量环境中的温度.传感器的解调通过自制的白光干涉解调仪实现,实验通过测量腔长得到被测环境的温度和气压.在不同温度和气压环境下,对腔长分别为306μm和1535μm的温度压力光纤传感器进行连续测量.实验结果表明,传感器能够在28~800℃的温度下和0~10 MPa的气压下稳定工作,测量范围内温度灵敏度可达17.4 nm/℃,压力灵敏度随温度增加而降低,在28℃时可达1460.5 nm/MPa.     

Study of water uptake in poly(ether ether ketone) irradiated by MeV O+ and Au+ ions

Poly(ether ether ketone) (PEEK) was irradiated with 4?MeV O⁺ and 5 and 10?MeV Au⁺ ions to the fluences from 10¹² to 10^14?cm^?2 and then treated in 5 M/l water solution of LiCl for one month at room temperature. After drying and removal of LiCl surface contamination, the depth distribution of LiCl embeded in PEEK was measured by the neutron depth profilig method (NDP) sensitive to ⁶Li isotope. Embeded LiCl is believed to map distribution of water diffusing into PEEK interior. The results show that the PEEK irradiated to the fluences above 1.10¹³cm^?2 is prone to water penetration to the depths of few microns. On the pristine PEEK and that irradiated to lower ion fluences only a surface Li contamination is observed.     

饮用水中三氯甲烷与其他氯消毒副产物在活性炭上的吸附竞争研究

通过等温吸附实验，探究了三氯甲烷（CHCl₃）与二氯一溴甲烷（CHBrCl₂）、二氯乙酸（Cl₂CHCOOH）在活性炭上的竞争吸附关系，同时探究了在低浓度条件下CHBrCl₂和Cl₂CHCOOH浓度变化对活性炭吸附CHCl₃的影响。实验结果表明，活性炭吸附CHCl₃和CHBrCl₂符合Freundlich模型，对Cl₂CHCOOH的吸附符合Langmuir模型；活性炭对3种消毒副产物均为优先吸附，吸附能力由大到小依次为CHBrCl₂、CHCl₃、Cl₂CHCOOH；低浓度条件下，活性炭对消毒副产物的吸附效果随体系中物质种类的增加而降低；低浓度条件下，Cl₂CHCOOH的浓度变化对CHCl₃的吸附效果影响不大，但吸附效果随水体中CHBrCl₂浓度的升高而降低。     

Organic–Inorganic Hybrid Zinc Phosphate with 28‐Ring Channels

An organic–inorganic hybrid zinc phosphate with 28‐ring channels was synthesized by use of an organic ligand instead of organic amine template under a hydro(solvo)thermal condition. This crystalline zinc phosphate contains large channels constructed from 28 zinc and phosphate tetrahedral units. The walls of the channels consist of two types of zincophosphate chains, in which the Zn atoms are coordinated by 2,4,5‐tri(4‐pyridyl)‐imidazole ligands as pendent groups. This compound exhibits yellow emission and interesting properties of removing cobalt, cadmium, and mercury cations from aqueous solution. A new two‐dimensional organic–inorganic hybrid zincophosphate was also obtained by changing the solvent mixture ratios in the synthesis.     

Comparison of monomethoxy‐, dimethoxy‐, and trimethoxysilane anchor groups for surface‐initiated RAFT polymerization from silica surfaces

The immobilization of reversible addition–fragmentation chain transfer (RAFT) agents on silica for surface‐initiated RAFT polymerizations (SI‐RAFT) via the Z‐group approach was studied systematically in dependence of the functionality of the RAFT‐agent anchor group. Monoalkoxy‐, dialkoxy‐, and trialkoxy silyl ether groups were incorporated into trithiocarbonate‐type RAFT agents and bound to planar silica surfaces as well as to silica nanoparticles. The immobilization efficiency and the structure of the bound RAFT‐agent film varied strongly in dependence of the used solvent (toluene vs. 1,2‐dimethoxyethane) and the anchor group functionality, as evidenced by atomic force microscopy, transmission electron microscopy, dynamic light scattering, and UV/Vis spectroscopy. Surface‐initiated RAFT polymerizations using functionalized silica nanoparticles revealed that grafted oligomers, which often occur in SI‐RAFT, are not formed within the crosslinked structures that originate from the immobilization, and that RAFT‐agent films that show less aggregation during the immobilization are more efficient during SI‐RAFT in terms of polymer grafting density. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 103–113     

Naphthalimide‐phthalimide derivative based photoinitiating systems for polymerization reactions under blue lights

Naphthalimide‐phthalimide derivatives (NDPDs) have been synthesized and combined with an iodonium salt, N‐vinylcarbazole, amine or 2,4,6‐tris(trichloromethyl)‐1,3,5‐triazine to produce reactive species (i.e., radicals and cations). These generated reactive species are capable of initiating the cationic polymerization of epoxides and/or the radical polymerization of acrylates upon exposure to very soft polychromatic visible lights or blue lights. Compared with the well‐known camphorquinone based systems used as references, the novel NDPD based combinations employed here demonstrate clearly higher efficiencies for the cationic polymerization of epoxides under air as well as the radical polymerization of acrylates. Remarkably, one of the NDPDs (i.e., NDPD2) based systems is characterized by an outstanding reactivity. The structure/reactivity/efficiency relationships of the investigated NDPDs were studied by fluorescence, cyclic voltammetry, laser flash photolysis, electron spin resonance spin trapping, and steady state photolysis techniques. The key parameters for their reactivity are provided. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 665–674     

Amphiphilic thermoset elastomers from metal‐free,click crosslinking of PEG‐grafted silicone surfactants

The hydrophobicity of silicone elastomers can compromise their utility in some biomaterials applications. Few effective processes exist to introduce hydrophilic groups onto a polysiloxane backbone and subsequently crosslink the material into elastomers. This problem can be overcome through the utilization of metal‐free click reactions between azidoalkylsilicones and alkynyl‐modified silicones and/or PEGs to both functionalize and crosslink silicone elastomers. Alkynyl‐functional PEG was clicked onto a fraction of the available azido groups of a functional polysiloxane, yielding azido reactive PDMS‐g‐PEG rake surfactants. The reactive polymers were then used to crosslink alkynyl‐terminated PDMS of different molecular weights. Using simple starting materials, this generic yet versatile method permits the preparation and characterization of a library of amphiphilic thermoset elastomers that vary in their composition, crosslink density, elasticity, hydrogel formation, and wettability. An appropriate balance of PEG length and crosslink density leads to a permanently highly wettable silicone elastomer that demonstrated very low levels of protein adsorption. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1082–1093